Cleaner spray
Cleaner and degreaser for all metals
Evaporates without leaving residues
For repair and assembly. Cleaner s spray s cleans
And degreases all metal surfaces, glass, ceramics
And most plastics. It may, however, etch the surface
Of thermo-plasts such as PVC, PMMA ( Plexiglas),
Polystyrene etc. as well as of simple paint coats.
Unlike ordinary thinners, cleaner spray s leaves no
Residues. Thanks to its special valve the spray can may
Be used in and position.
Applications:
– On brakes ( drum and disk brakes, linings, brake pads,
Cylinders, springs and bushes)
– On clutches (clutch linings and components)
– On engine components (carburetors, fuel and oil
Pumps, transmissions etc.)
– As a pretreatment of parts, when a greasy surface would
Affect performance
Directions:
Spray cleaner s in sufficient quantity onto the part to be
Treated and allow to react. If necessary, wipe off with a
Clean cloth. Repeat process as required. Avoid contact
With plastic and varnished surfaces.
FUEL injector CLEANER & Carburetor
General Description
Fuel injection air intake cleaner safe for catalytic converters and
oxygen sensor, Fuet injection air intake cleans, protects and
lubricates butterfly/throttle body and idle intake control valves,
use every three months or 20,000 km.
Direction: attach extension tube to button.
note: never spray on hot engine. For engines that will run with air
intake hose removed use directions.
If sprayed on, do rub surfaces flush with water immediately.
Precautions
Fire and explosion hazard: use only in well-ventilated area away
from heat, sparks, and flame. Pilot tights of furnaces or hot water
tanks, or seven static electricity, can ignite vapors explosively.
Insure adequate ventilation, especially in confined spaces suchas
enclosed garages, engine compartments of boats or vans, or other
low lying areas where vapors can collect.
Do not place can on hot surfaces or in direct sunlight, which could
cause can to burst viotently. Keep can from contact with electrical
current or connectionis (such as buttery terminals) because
burn-though may occur.
Explosion or flash fire from liquid or vapors may cause serious
injury or death, toxic decomposition can occure.
Caution
1.Extremely flammable do not spray near sparks, heat or open
flame do not store in direct sunlight, 2, keep area ventilated during
use, 3, keep out of reach of children.
4, Do not puncture,incinerate,burn or shore of above 48O C.
Breathing hazard: do not breathe vapors or mist.
Use approved respirator. use only in well-ventilated area.
Open doors and windows to prevent vapor bulild up.
Contact hazard: avoid contact with eyse. Skin,or clothing.
repeated contact may dry and defeat the skin.
remove contaminated clothing and wash befor use.
wear chemical goggles and solvent-proof gloves and apron.
If eye contact, wash them immediately with clean water and seek
medical advice.
Spray Grease
All-purpose spray able grease
Spray grease yellowish is a multi -purpose Lithium EP soap
Spray able grease yellowish an outstanding adhering
Strength and excellent aging and pressure
Resistance. The addition of special lubricants wear-
Reducing and corrosion-inhibiting additives
Allows it to achieve temperature stability from
-30OOc to +140OOc in combination
With a long service life. As with white
Products, a visual inspection is possible at All times.
OBS spray grease yellowish can be
Used for the long-term lubrication of rods,
Gearwheels, rollers, ball bearings, hinges,
Guides and all types of joints and couplings
In many heavy loads industrial applications
Warning
Keep away from sunlight and keep it at a temperature below 50⁰c
Oil lubricant
This spray is oily transparent and adherent lubricant for
the lubrication of highly stressed mechanical parts of all kinds.
It resists temperatures from -20°C to +120°C compression
resistant,resistant,creeping and water repellent properties.
Prevents friction and wear.
Limited resistance is given for: PE-LD, POM, PP, NBR
Applications:
For long-lasting lubrication of
- power-transmitting bolts and pins
- toothed wheels and wormgear
- fast-moving engine parts
- joints and clutches
- roller and ball bearings
Directions:
Surfaces to be treated must be clean and dry. Shake can and
spray at about 15 cm from surface.
Product may,thereafter, be applied also while parts to be
lubricated are in operation, subject to respect of the relevant
safety regulations..
English 
Persian